Planet Technology WDAP-2000PE Bedienungsanleitung

54/108Mbps Super A+G Wireless Access Point WDAP-2000PE User’s Manual

Installation 2 Chapter 2 Installation 2.1 General Installation Before you proceed with the installation, it is necessary that you have enough informat

3 Chapter 3 Setup & Management 3.1 Overview This chapter describes the setup procedure to make the WDAP-2000PE a valid device on your LAN, and to

If you can't connect: It is likely that your PC’s IP address is incompatible with the WDAP-2000PE’s IP address. The default IP address of the Wi

Assign static IP to this device If selected, the following data must be entered. • IP Address - The IP Address of this device. Enter an unused IP

Network ID (SSID) The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging

rity Policy connect to your network. WEP: WDAP-2000PE allows you to use WEP data encryption to secure your data from being eavesdropping by unauthori

3.4 Device Status You can monitor the system general information from the Device Information field. 3.4.1 System Log The system log allows you to t

3.4.3 Bridge Table The bridge table shows all MAC entries learned from the wired LAN interface, wireless clients, and WDS peers (if running in the

3.4.4 Radio Table Radio table lists current Mode, channel, client associated with them and transmit packet, re-ceived packet, data error. 3.4.5 Sit

3.5 Advanced Settings The advanced settings tab contains more configurations for experienced users. However, changing your login password from the d

Copyright Copyright© 2005 by PLANET Technology Corp. All rights reserved. No part of this publica-tion may be reproduced, transmitted, transcribed,

Local Management This option allows you to enable/disable management from WLAN connection. System Administration The Access Point allows you to des

Bridge You can enable/disable the 802.1d STP (Spanning Tree Protocol) function on the bridge of WLAN and Ethernet (i.e. the LAN inter-face). Enable t

are enabled, the device can send out TRAP messages automati-cally to the TRAP manager if configured. Assign System Informa-tion System Name: A name t

Disable MAC address control list When selected, no MAC address filtering will be performed. Enable GRANT address control list When selected, data t

Enable VLAN for all SSIDsOnce this function is enabled, you can specify an individual VLAN ID and priority tag for each SSID. In this way, you can

Select security policy Configure the security policy for the SSID. 3.5.6 Wireless Settings Beacon interval The WDAP-2000PE broadcasts beacon frame

Fragmentation When the size of a unicast frame exceeds the fragmentation threshold, it will be fragmented before the transmission. It should have a v

ure WDS devices. Access Point This means the device is working on AP-only Mode, and is for wireless client users only. Wireless Distribution System (

Enable Primary/Secondary Server Check this if you want to enable RADIUS authentication using the primary/secondary Radius Server. If both are selecte

Ping flooding filtering When the ping (to the AP) traffic reaches the configured degree (e.g. High, Low), any more such ping packets will be dropped.

Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the

3.6 System Tools 3.6.1 Firmware Upgrade You can upgrade the firmware of your WDAP-2000PE. Normally, this is done when a new version of firmware is r

3.6.2 Configuration Save and Restore You can save system configuration settings to a file, and later download it back to the WDAP-2000PE by following

3.6.3 Factory Default You can reset the configuration of your WDAP-2000PE to the factory default settings. Step 1: Select Factory Default from the S

Chapter 4 PC and Server Configuration 4.1 Overview All Wireless Stations need to have settings which match the Wireless Access Point. These settings

Security • The Pre-shared Key entered on the WDAP-2000PE must also be entered on each Wireless client. • The Encryption method (e.g. TKIP, AES) mus

• rras • webserver (IIS) • Radius Server (Internet Authentication Service) • Certificate Authority 4.5.1 Windows 2000 Domain Controller Setup

6. Enter the information for the Certificate Authority, and click Next. 7. Click Next if you don't want to change the CA's configuratio

3. Click Next when the New Scope Wizard Begins. 4. Enter the name and description for the scope, click Next. 5. Define the IP address range. Cha

11. If you don't want a WINS server, just click Next. 12. Select Yes, I want to activate this scope now. Click Next, then Finish. 13. Right-c

4. Select Start - Programs - Administrative Tools - Active Directory Users and Com-puters. 5. Right-click on your active directory domain, and sele

TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ... 3 1.1 Package Contents ...

7. Select Computer Configuration - Windows Settings - Security Settings - Public Key Policies, right-click Automatic Certificate Request Settings -

10. Ensure that your certificate authority is checked, then click Next. 11. Review the policy change information and click Finish. 12. Click Start

9. Click Permitted, then OK. Select Next. 10. Select Grant remote access permission. Click Next. 11. Click Edit Profile... and select the Authentic

3. Select the Dial-in tab, and enable Allow access. Click OK. 4.6 802.1x Client Setup on Windows XP Windows XP ships with a complete 802.1x clien

4. On the first screen (below), select Request a certificate, click Next. 5. Select User certificate request and select User Certificate, the clic

6. Click Submit. 7. A message will be displayed, then the certificate will be returned to you. Click Install this certificate. 43

8. . You will receive a confirmation message. Click Yes. 9. Certificate setup is now complete. 4.6.2 802.1x Authentication Setup 1. Open the p

Encryption Settings The Encryption settings must match the APs (WDAP-2000PE) on the Wireless net-work you want to join. • Windows XP will detect an

2. Select the wireless network from the Available Networks list, and click Configure. 3. Select and enter the correct values, as advised by your N

4.7 Using 802.1x Mode The procedures are similar to using 802.1x. The only difference is that on your client, you must NOT enable the setting: The ke

4.5.6 Grant Remote Access for Users ... 40 4.6 802.1x Client Setup on Windows XP ...

A Appendix A Troubleshooting Problem 1: Can't connect to the WDAP-2000PE to configure it. Solution 1: Check the following: • The WDAP-2000PE

Appendix B Command Line Interface If desired, the Command Line Interface (CLI) can be used for configuration. This creatpossibility of creating scrip

Description: Set the HTTP server port (for device management) to the one specified. set http timeout <timeout value in minutes, 1-60> Descripti

show snmp statistics Description: Display the current SNMP statistics. show trap manager [<string up to 30 characters>] Description: Display th

Chapter 1 Introduction PLANET WDAP-2000PE is an IEEE 802.11a+g dual band Wireless Ac-cess Point with PoE. With the latest innovative Super A/G techno

1.3 Physical Details Top View LED Status Description POWER PWR Steady Green – Power on OFF – Power off Link/ActSteady Green - Link is active Flash

Installation Rear View Connector Description ANT Two dipole antennas are supplied. Best result is usually obtained with the antenna in a vertical po

Management Web based configuration CLI configuration Message Log Firmware upgrade UPnP support Configuration file Backup/Restore Super A/G mode Up to