Planet Technology WSD-800 Bedienungsanleitung Seite 1

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -1- User's Manual WSD-800 8-Port 10/100Mbps WGSD-910 8-Port 10/100Mbps + 1 Gigabi

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -10- 2. INSTALLATION This section describes the functionalities of the Switch's components and gu

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -100- Figure 7-4 Assign Port-1 to be VLAN 2 and VLAN 3 member. 7. After the down the Port 1 VLAN co

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -101- Figure 7-6 Port 1, Port 2 and Port 3 VLAN configuration Although Port 2 and Port 3 are VLAN 1

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -102-  VLAN Group Membership VLAN ID VLAN Define Major Member VLAN 1 Public VLAN WGSW-2840_220

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -103- Port3 Always Untag 1 Untag=1,2,3,4 NtworkPrinter Port28 Trunk 1 Tag=1,2,3,4 Core-2840 

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -104-  802.1Q VLAN - Multi-Untagged VLAN setting sample 3  VLAN Group Membership VLAN ID VLA

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -105- [192.168.0.20] switch Client connect to Ports those be assigned to VLAN 3 ,at [192.168.0.30] s

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -106-  WGSW-2840_192.168.0.30 Edge-Switch VLAN Configuration 192.168.0.30 VLAN Configuration Port

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -11- Figure 2-3 shows the front panel of WGSD-1022C. Figure 2-3 WGSD-1022C front panel. 2.1.3 LED In

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -12- Gigabit TP/SFP interface (Port-9, WGSD-910), (Port-9, Port-10, WGSD-1022C) LED Color Functi

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -13- 2.2 Install the Switch This section describes how to install the Ethernet Switch and make connect

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -14- 2.2.2 Rack Mounting To install the Switch in a 19-inch standard rack, please follows the instruct

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -15- 2.2.3 Installing the SFP transceiver The sections describe how to insert an SFP transceiver into

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -16- Connect the fiber cable 1. Attach the duplex LC connector on the network cable into the SFP tran

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -17- 3. CONSOLE MANAGEMENT 3.1 Connecting to the Switch The console port is a female DB-9 connector th

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -18- After finished the parameter settings, click “OK“. When the prompt shows “Switch>”, type “?” f

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -19- 3.4 Telnet login The Switch also supports telnet for remote management. The Switch asks for user

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -2- Trademarks Copyright © PLANET Technology Corp. 2008. Contents subject to which revision without pr

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -20- show qos map dot1p-cos-map Show qos map cos-queue-map show qos map mac-cos-map Show qos map mac

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -21- clear port spantree portpri Restore spanning tree port priority to default value clear port stor

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -22- 3.5.2.4 Reboot command Reboot command is to reboot the Switch, please beware to check if the conf

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -23- set ipstack disable Set ipstack disable set ipstack group Set ipstack group STR set ipstack mac

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -24- set security mac-learning Set port leanrning MAC (enable|disable) set security static-MAC Creat

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -25- show igmp-snooping Show igmp snooping information show ip http server Show http server informat

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -26- 4. WEB-BASED MANAGEMENT This section introduces the configuration and functions of the Web-Based

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -27- WSD-800 Web Management Interface 4.4 System 4.4.1 IP Configuration The Switch ca

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -28- IP Address Configuration NOTE: 1. The Switch’s factory-default IP address is 192.168.0.100 with

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -29- SNMP Operations SNMP itself is a simple request/response protocol. NMSs can send multiple request

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -3- Table of Contents 1. INTRODUCTION...

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -30- 2. System Options This table is to define the system name, system location and the contact perso

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -31- 4. Management Station Configuration A trap manager is a management station (SNMP application) t

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -32- 4.4.3 Password The Password management menu is to set or change the password of the Web Managemen

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -33- 4.4.6 Saving Parameters It takes effect immediately when you change the parameters of the managem

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -34- 4.4.8 Load Default This function is to reset the configuration of Switch to the factory default.

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -35- 4.5 Port Management 4.5.1 Port Configuration This function is to configure and to view the config

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -36- 4.5.3 Port Band Restrict The function provides the In-Band and Out-Band connection speed restrict

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -37- Spanning Tree Algorithm and protocol are a complicated and complex subject and must be fully rese

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -38- STP Port States The BPDUs take some time to pass through a network. This propagation delay can re

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -39- You can modify each port state by using management software. When you enable STP, every port on e

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -4- 4.4.8 Load Default...

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -40- The following are the user-configurable STP parameters for the port or port group level: Variable

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -41- Max. Age _ 2 x (Hello Time + 1 second) Port Priority – A Port Priority can be from 0 to 255. The

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -42- Root BridgePort 3Port 1Port 2ADesignated BridgePort 1Port 2Port 3CPort 1Port 2Port 3B LAN 1 LAN

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -43- 2. Bridge Information The informations of the STP Root show in the Bridge Information table. 3.

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -44- unless manually overridden through configuration. The link type attached to this port could be se

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -45- 4.6.3 Link Aggregation Link aggregation can be used to increase the bandwidth of a network connec

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -46- 4.7 Security 4.7.1 VLAN 4.7.1.1 Theory Understanding IEEE 802.1p Priority Priority tagging is

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -47- that packets are forwarded only between ports within the VLAN. Typically, a VLAN corresponds to a

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -48- headers. The tagging feature allows VLAN to span multiple 802.1Q-compliant switches through a sin

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -49- 802.1Q Tag User Priority CFI VLAN ID (VID) 3 bits 1 bits 12 bits TPID (Tag

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -5- 6.1 CONSOLE PORT PIN ASSIGNMENTS ...

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -50- Because some devices on a network may be tag-unaware, a decision must be made at each port on a t

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -51- 6. Click on the “Close” button and back to the Port-based VLAN main page. The “Show VLAN Member”

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -52- only used internally within the Switch). Untagging is used to send packets from an 802.1Q-complia

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -53- The main page then changes to the 802.1Q VLAN table which displays the VLAN configuration of each

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -54- 5. Trunk configuration: If the Trunk type is chosen, please follow the steps to set the Trunk of

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -55- 4.7.2 MAC Address Bind This function is based upon for the Switch security. When you add one MAC

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -56- 4.7.3 MAC Address Filtering MAC address filtering allows the Switch to drop unwanted traffic. Tr

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -57- 4.7.4 MAC Address Learning The Switch is able to disable MAC Address learning function on ports.

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -58- percentage of received packets whose source addresses cannot be found in the forwarding table, in

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -59-  Device Roles With 802.1X port-based authentication, the devices in the network have specific r

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -6- 1. INTRODUCTION 1.1 Packet Contents Check the contents of your package for following parts: ▫ E

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -60-  Authentication Initiation and Message Exchange The Switch or the client can initiate authentic

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -61-  Ports in Authorized and Unauthorized States The Switch port state determines whether or not t

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -62- If the link state of a port transitions from up to down, or if an EAPOL-logoff frame is received,

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -63- 。 Auto: enables 802.1X authentication and causes the port to begin in the unauthorized state, al

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -64- ● Radius Server — In this situation, need a Radius server in the network, the normal topologies

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -65- • RADIUS Server IP Address The IP address of the RADIUS server being added. • Authentication Port

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -66- 4. Configure ports attribute of 802.1X, the same as “802.1X Port Status Configuration”. NOTE: S

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -67- Enter ” Active Directory Users and Computers”, create legal user data, the next, right-click

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -68- 6. The last, run your 802.1X Client 4.7.6.3 802.1X Client Configuration Windows XP is original

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -69- 4. Select “Authentication” tab. 5. Select “Enable network access control using IEEE 802.1X” to

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -7- 1.3 Product Feature ▫ Complies with IEEE 802.3, 10Base-T, IEEE 802.3u, 100Base-TX, IEEE 802.3ab,

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -70- 9. Enter the user name, password and the logon domain that your account belongs. 10. Click “O

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -71- 4.8 QoS 4.8.1 Understand QOS Quality of Service (QoS) is an advanced traffic prioritization fea

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -72- 2. Apply a classifier to determine how the incoming traffic will be classified and thus treated

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -73- 2. VLAN-COS Mapping QoS settings allow customization of VLAN ID to Traffic classifiers 1. Fill t

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -74- 3. 802.1p-CoS Mapping QoS settings allow customization of packet priority in order to facilitat

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -75- 4. Port-COS Mapping QoS settings allow customization of VLAN ID to Traffic classifiers 1. Fill t

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -76- 6. Queue Management There are two rules for the Priority Queue: Weighted Round Robin (WRR) and A

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -77- 4.9 Multicast 4.9.1 IGMP Snooping Theory Computers and network devices that want to receive multi

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -78- A host will never send a report when it wants to leave a group (for version 1). A host will send

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -79- 4.9.3 IGMP Port Policy For the security and management issue, the Switch is allowed to limiti

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -8- Switch Throughput 1.19Mpps 2.67Mpps 4.16Mpps Switch Architecture Store-and-Forward Address Table

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -80- Configure Sample: 1. Select the Port field in the Set IGMP Port Policy Table, in this case, Por

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -81- The maximum number of IGMP multicast groups are restricting to 4 entries; the more IGMP Join pac

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -82- IGMP Group-Policy Application  Delete: Delete an exist Multicast Group entry IGMP Group-Policy

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -83-

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -84- 4.9.5 Static Routing Port This function is to configure ports to be the member of IGMP Groups in

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -85-  Static Routing Port and Multicast group VLAN member configue 1. Enable IGMP Snooping, as the

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -86- NOTE: The Multicast group VLAN member must be configured first, and then setup the Static Routi

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -87- 4.10 Port Analysis 4.10.1 Port Analysis This function shows the statistical information of each p

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -88- 4.11 Storm Control This function is to control the Braodcast Storm, Multicast Storm and Flooded

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -89- 4.12 IP Stacking 4.12.1 About IP Stacking IP Stacking function enables you to use a single IP a

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -9- Security MAC filtering and Binding, up to 400 rules SNMP MIBs RFC-1213 MIB-II RFC-2863 Interface M

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -90- • Master – The IP Stacking Management status is enabled and the current switch is a Master switc

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -91- WGSW-5240 Switches as Master in Management mode field, the following screen appears. 3. Enter

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -92- 8. Enter a string in the “IP Stacking Group” field; the default string of the WSD-800 / WGSD-910

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -93- NOTE: Please do not assign role for whole stack member Switch as client, it cannot detect the M

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -94- 5. TROUBLE SHOOTING This section is intended to help you solve the most common problems on the WS

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -95- 5.2.1 Cabling RJ-45 ports: use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable f

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -96- 6. APPENDIX 6.1 Console Port Pin Assignments The DB-9 serial port on the front panel is used to

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -97- 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-FX 50/125 or 62.5/125 micron core m

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -98- 7. APPENDIX-B  802.1Q VLAN Multi-Untagged VLAN setting sample 1 The version V.1.4.27 of PLANET

User’s Manual of WSD-800 / WGSD-910/WGSD-1022C -99- Figure 7-2 802.1Q VLAN page screen 3. Move the mouse course to the port, which had be assigne