Planet-technology FT-1205A Bedienungsanleitung

10/100Base-TX to 100Base-FXRedundant Media ConverterFT-1105A / FT-1205AUser’s Manual

10Chapter 3 CHECKLISTYour FT-1105A / FT-1205A carton should contain the following items: The Redundant Fast Ethernet Converter AC-DC Power A

11Chapter 4 PRODUCT OUTLOOKFT-1105A Front Panel● Port-1 100Base SFP slot● Port-2 TP connector (Primary Port)● Port-3 TP connector (Backup Port)FT-1

12Chapter 5 DIP SWITCHThere is a DIP switch for the setting on converter mode of copper and ber port. Refer to the table below for more de

13FT-1205ASwitch 1On 2-Port Redundant (Fiber)Off 3-Port Switch (default)Switch 2On LBR ONOff LBR OFF (default)2-Port Redundant (FT-1205A)When Fiber

14Chapter 6 INSTALLING THE CONVERTER 6.1 Stand-alone InstallationFT-1105A / FT-1205A is with high reliability and exibility to extend the di

15NoteIt recommends using PLANET MFB-FX series 100Base-FX SFP on the converter. If you insert a SFP transceiver that is not supporte

16Step 2: Carefully slide in the module until it is fully and rmly tted into the slot of the chassis. Figure 2-1: Insert a media converte

17Chapter 7 RedundancyThe FT-1105A / FT-1205A provide less than 10ms link redundancy for highly critical Ethernet applications. The redu

18Chapter 8 Loop Back ReplyThe FT-1105A / FT-1205A supports auto loop back reply while receive loop back test packets on ber port. Enable th

19Chapter 9 LED INDICATORSThe LED indicators give you instant feedback on status of the converter: SystemLED Color FunctionPWR Green Lit: Po

TrademarksCopyright © PLANET Technology Corp. 2007.Contents subject to which revision without prior notice.PLANET is a registered trademark of P

20LED Color FunctionLNK/ACTGreenLit: Indicate that the port is link up.Blink:Indicate that the converter is actively sending or receiving data over th

21Chapter 10 PRODUCT SPECIFICATIONModel FT-1105A FT-1205APortsCopper 2 x 10/100Base-TX port 1 x 10/100Base-TX portFiber 1 x 100Base-FX port 2 x 100Ba

22APPENDIX AA.1 Device's RJ-45 Pin Assignments10/100Mbps, 10/100Base-TXContact MDI MDI-X1 1 (TX +) 32 2 (TX -) 63 3 (RX +) 16 6 (RX -) 24, 5, 7,

23There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cab

24A.4 Power InformationThe power jack of FT-1105A / FT-1205A is with 2.5mm in the central post and required +5VDC power input. It will conf

FCC WarningThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC R

RevisionPLANET Fast Ethernet Redundant Media Converter User’s ManualFOR MODELS: FT-1105A / FT-1205ARevision: 1.1 (November, 2007)Part No.: 2010-AA3520

Table of ContentsChapter 1 OVERVIEW ... 6Chapter 2 PRODUCT FEATURES ...

6Chapter 1 OVERVIEWThank you for choosing the Smart 10/100Base-TX to 100Base-FX Media Converter, The Media Converter introduced here pr

7network. The SFP slot supports single-mode, multi-mode and WDM small-form factory type transceiver modules for your needs. With 100Base

8Chapter 2 PRODUCT FEATURESStandard• Complies with IEEE 802.3, IEEE 802.3u 10/100Base-TX, 100Base-FX• IEEE 802.3x Full-Duplex Flow-Control,

9● DIP Switch for 3-Port operation with Fast Ethernet switch mode or Redundant mode● DIP switch for LPR (Loop back Reply) on / off selection