Planet-technology XRT-412 Bedienungsanleitung

Internet Broadband Router XRT-412 User’s Manual 1

8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. "Note: Please make sure

5: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. "Note: Ple

5: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address automatically and Obtain DNS server address automatically as s

4: In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok button to start installing the TCP/IP protocol. You may ne

3) Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automatically give your LAN clients an IP a

The Status Information section is for you to monitor the router’s current status information only. Tools (Chapter 5) If you want to Reset the router

7) Click on Quick Setup Wizard (see chapter 2) to start configuring settings required by your ISP so that you can start accessing the Internet. The

Chapter 2 Quick Setup The Quick Setup section is designed to get you using XRT-412 as quickly as possible. In the Quick Setup you are required to fill

"Note: Different ISP’s require different methods of connecting to the Internet, please check with your ISP as to the type of connection it requi

2.1 Cable Modem Choose Cable Modem if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional info

Copyright Copyright (C) 2006 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed prod

2.2 Fixed-IP xDSL Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information re

2.3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required i

WAN line breaks down and latter links again, the router will not auto-connect to the ISP. Idle Time You can specify an idle time threshold (minutes)

2.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in t

Password Enter the Password provided by your ISP for the PPTP connection. PPTP Gateway If your LAN has a PPTP gateway, then enter that PPTP gateway

2.5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in t

L2TP Gateway If your LAN has a L2TP gateway, then enter that L2TP gateway IP address here. If you do not have a L2TP gateway then enter the ISP’s Ga

2.6 Telstra Big Pond Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet. Your ISP should provi

23

Chapter 3 General Settings Once you click on the General Setup button at the Home Page, you should see the screen below. If you have already configur

Trademarks The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware and software products by their trade

3.1 System The system screen allows you to specify a time zone, to change the system password and to specify a remote management user for XRT-412.

Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your selection. Time Server Address

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the rout

3.2 WAN Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and you would like to change your Internet connecti

3.2.1 Dynamic IP Choose the Dynamic IP selection if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in a

Parameters Description Domain Name Server (DNS) Server This is the ISP’s DNS server IP address that they gave you; or you can specify your own

Parameters Default Description Enable/Disable Disable Enable/Disable the DDNS function of this router Provider

802.1d Spanning Tree Disabled If 802.1d Spanning Tree function is enabled, this router will use the spanning tree protocol to prevent from network

Parameter Description 3.4.1 Port Forwarding You can have different services (e.g. email, FTP, Web etc.) going to different service servers/cli

3.4.1 Port Forwarding The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a partic

TABLE OF CONTENTS Chapter 1 Introduction ...1 1.1 Features ...

Table", select the Port Forwarding settings you want to remove in the table and then click "Delete Selected". If you want remove all Po

Type Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocols. Public Port Enter th

Parameters Description Enable Trigger Port Enable the Special Application function. Trigger Port This is the out going (Outbound) range of po

added into the "Current Trigger-Port Table" below. If you find any typo before adding it and want to retype again, just click "Clear&qu

Parameters Default Description UPnP Feature Disable You can Enable or Disable UPnP feature here. After yo

Parameters Default Description Enable You can select to enable “Application Layer Gateway” of an application and then the router will let that

Parameters Description 3.5.1 Access Control Access Control allows you to specify which hosts users can or cannot have access to certain Internet

Parameters Description Enable MAC Filtering Check “Enable MAC Filtering” to enable MAC Filtering, select “Deny” or “Allow” to define the acces

Add PC Parameters Description Client PC Description The description for this client PC rule. Client PC IP Address Enter the IP address rang

Protocol This allows you to select UDP, TCP or both protocol types you want to block. Port Range You can assign up to five port ranges. The router

4.3 Device Status ...54 4.4 System Log ...

3.5.3 Denial of Service (DoS) The XRT-412's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan and

Parameters Description Enable DMZ Enable/disable DMZ Note: If there is a conflict between the Virtual Server and the DMZ setting, then Virtual

3.6 Print Server The print server provides LPR and IPP printing methods. You can enable/disable the print server function and change the print server

2. Click “Next” and specify the destination folder where the utility will be installed. 3. Click “Next” and specify the program folder where the

4. Click “Next” to start installation. 5. In a while, the program will finish installing all the utilities and drivers. Thus far you have comple

6. Click “Continue”, and all the print server’s network ports detected on the network will be added to your PC. 7. Finally, the “Installation com

4. Select “Use following port”, and choose XRT-412 printer name and Queue name, then to click “Next”. 51

5. Select the suitable printer manufacturer and model, then click “Next” 6. Complete the rest of the questions to finish the network printer setup

Chapter 4 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection st

Parameters Description Information You can see the router’s system information such as the router’s: LAN MAC Address, WAN MAC Address, Hardware ve

Chapter 1 Introduction Congratulations on purchasing PLANET XRT-412. This Broadband Router is an IP Sharing Router that enables multiple users to sha

Parameters Description Device Status This page shows XRT-412’s current device settings. This page displays XRT-412 LAN port’s current LAN IP Add

or can be refreshed <Refresh> to get the most updated situation. The log only records the information of current session and will be cleared w

Parameters Description DHCP Client Log This page shows all DHCP clients (LAN PCs) currently connected to your network. The “Active DHCP Client”

Chapter 5 Tools This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings), Firmware Upgra

Parameters Description Configuration Tools Use the "Backup" tool to save XRT-412 current configuration to a file named "config.bi

file name and path in the appropriate field on this page. You can also use the Browse button to find the firmware file on your PC. Once you’ve

Appendix A How to Manually find your PC’s IP and MAC address 1) In Window’s open the Command Prompt program 2) Type ipconfig /all and <enter&

• Your PC’s IP address is the one entitled IP address (192.168.0.7) • The router’s IP address is the one entitled Default Gateway (192.168.0.1) • Y

Glossary Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP pack

ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet router located at the ISP's office. ISP

from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So pl

Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configur

LED Light Status Description PWR ON Router’s power supply is on USB1 Flash

1.6 Getting started This is a step-by-step instruction on how to start using the router and get connected to the Internet. 1) Setup your network a